Kenmore 469085 Replacement Refrigerator Water Filter 1 Pack

Also sold under the part numbers 46-9085 and 9085, this filter is a compatible replacement designed to restore clean, fresh-tasting water and ice to select Kenmore side-by-side refrigerators. It's certified to NSF/ANSI 42, 53, and 401 for contaminant reduction, installs without tools in about a minute, and is rated for up to 6 months of typical household use.

Product Overview

If your Kenmore refrigerator's water or ice has started to taste flat, smell off, or flow more slowly than usual, it's usually a sign the filter has reached the end of its service life. The Kenmore 469085 filter — labeled interchangeably as 46-9085 or 9085 depending on packaging — replaces the cartridge inside your fridge's filtration system, trapping sediment and reducing common tap-water contaminants before they reach your glass or ice maker. It uses the same twist-and-lock cap design as the OEM cartridge it replaces, so no plumbing knowledge or tools are required to swap it out.

Compatibility — Is This the Right Filter for Your Refrigerator?

This filter is built to fit select Kenmore and Kenmore Elite side-by-side refrigerators that originally used any of the part numbers below. Because Kenmore has re-labeled this filter several times over the years, checking both your old filter's part number and your refrigerator's model number (usually on a sticker inside the door frame or behind the crisper drawer) is the most reliable way to confirm fit before ordering.

This filter replaces the following earlier Kenmore part numbers:

If your old filter or refrigerator manual references any of these numbers, the 469085 / 46-9085 / 9085 filter is the correct current replacement. If you're not sure which filter your model uses, our Kenmore Refrigerator Water Filters collection page can help you cross-check by model, or you can contact our support team before ordering.

Product Specifications

Key Features and Benefits

• NSF-certified filtration — independently tested to NSF/ANSI 42, 53, and 401 standards for contaminant reduction

• No-tools installation — twist-and-lock cap design means most homeowners can complete a swap in a few minutes

• No water shutoff needed — the filter housing seals automatically, so there's no need to turn off your home's water supply

• Consistent water flow — a properly seated, fresh filter helps maintain steady dispenser flow and clearer ice

• Drop-in fit — designed to match the same footprint and mechanism as the original Kenmore cartridges it replaces

What Does This Filter Reduce?

This filter is certified to NSF/ANSI 42, 53, and 401 to reduce a range of common water impurities, including:

• Chlorine taste and odor

• Lead and select heavy metals

• Sediment and particulates

• Trace pharmaceuticals

Certification does not mean every contaminant listed is present in your water supply — actual results depend on your local water quality. If you want to see the specific standards, NSF publishes a public overview of what NSF/ANSI 42, 53, and 401 each cover.

How to Install the Filter

1. Locate the filter housing. On most compatible Kenmore side-by-side models, this is in the base grille at the bottom-front of the refrigerator, behind a small plastic cover.

2. Release the old filter. Press the eject or release button next to the filter cap, then twist the cap counterclockwise to remove the old cartridge.

3. Transfer the cap. If your model uses a reusable decorative cap, remove it from the old filter and snap it onto the new one.

4. Insert the new filter. Push the new cartridge into the housing and twist clockwise until it locks into place — no tools and no water shutoff needed.

5. Flush the line. Run 2–3 gallons of water through the dispenser before drinking it. This clears trapped air and any loose carbon fines from the new filter — skipping this step is the most common cause of sputtering water or cloudy ice after a filter change.

6. Reset the filter indicator, if your model has one, following your refrigerator's control panel instructions.

For a full visual walkthrough, see our Kenmore water filter replacement guide.

When Should You Replace the Filter?

Replace your Kenmore 469085 filter:

• Every 6 months, as a general rule for most households

• Sooner, if you notice slower water flow from the dispenser

• Sooner, if water or ice develops an off taste or odor

• When your fridge's filter indicator light turns on (if your model has one)

Sticking to a regular replacement schedule protects your refrigerator's water valve from sediment buildup and keeps filtration performance consistent. For more on timing, see our guide on how often to replace a refrigerator water filter.

What's Included / Shipping & Returns

Each order includes one Kenmore 469085 replacement water filter cartridge, ready to install. Orders ship free within the USA, and if a filter arrives damaged or turns out not to fit your model, our return and refund policy covers you. Questions before you buy? Reach our team via the Contact Us page or check our FAQ.

Frequently Asked Questions

Is the Kenmore 469085 the same as the 46-9085 or 9085 filter?

Yes. These are all labels for the same filter — Kenmore has used 469085, 46-9085, and 9085 interchangeably on packaging over time.

Is this a genuine Kenmore part or a compatible replacement?

Yes

Does this filter fit all Kenmore refrigerators?

No. It's designed for select Kenmore and Kenmore Elite side-by-side models that originally used part numbers 9902, 9908, 2203221, 2203980, 2255520, 4392922, or 8212491. Confirm your refrigerator's model number before ordering.

How often should I replace it?

Every 6 months under typical use, or sooner if you notice reduced water flow, a change in taste or odor, or your fridge's filter indicator light turns on.

Do I need tools or to shut off my water supply to install it?

No. The filter uses a tool-free twist-and-lock cap, and the housing seals automatically when the old filter is removed, so there's no need to shut off your home's water line.

Why does my water sputter after installing a new filter?

This is normal and caused by trapped air in the line. Run 2–3 gallons of water through the dispenser after installation to clear the air and any loose carbon particles.

What does this filter reduce?

It's certified to NSF/ANSI 42, 53, and 401 to reduce chlorine taste and odor, lead, sediment, and trace pharmaceuticals. Actual results depend on your local water supply.